Top 10 typical forklift mishaps ， forklift procedure should take notice of these matters ！.

Do not take too lightly the forklift at work. If the operation is not good, there will be major crashes in minutes, and there are several mishaps including forklifts.

Situation 1: The forklift cargo obstructed the vehicle driver's view, and the person in front can not be discovered, leading to a rolling crash.
Instance 2: In order to preserve the equilibrium of the forklift when lifting hefty items, the staff members used their body weight as the weight, which practically triggered casualties.
Case 3: The size of the forklift cargo surpasses the allowable size of the course and hangs on the roadside rack, which virtually creates an crash.
Case 4: Forklift is speeding and rolls over during a turn.
Instance 5: The forklift driver did not notice the pedestrian, and the pedestrian did not see the forklift.
Situation 6: The forklift raises the employees illegally, the forklift motorist does not use the safety belt, the forklift lifter drops and the vehicle driver is crushed when the forklift rolls over.
Instance 7: The forklift driver did not wear a safety belt and dropped from the vehicle when it surrendered and was squashed.
Forklift operation need to focus on these issues ：.

Start.
1. Prior to beginning, observe the environments, and after confirming that there are no challenges that impede the safety and security of driving, beep the horn initially and after that start.
2. For lorries with hydraulic ( atmospheric pressure) brakes, the brake hydraulic stress ( atmospheric pressure) scale should be safe prior to beginning.
3. When the forklift begins with a lots, the chauffeur ought to initially verify that the lots is steady and trustworthy.
4. The begin needs to be sluggish and steady.

Driving.
1. When driving, the elevation in between the bottom end of the fork and the ground ought to be kept at 300mm-400mm, and the pole should be slanted backwards. .
2. Do not raise the fork too expensive when driving. When getting in and leaving the job website or while driving, be careful that there will be no challenges overhead. When the load is traveling, the fork needs to not be elevated too high, which will influence the stability of the forklift. .
3. After dumping, the fork must be lowered to the regular driving setting prior to driving. .
4. When transforming, if there are pedestrians or automobiles nearby, the driving signal ought to be issued initially. High-speed sharp turns are prohibited. High-speed sharp turns will certainly cause the vehicle to lose lateral security and topple. .
5. When the forklift is downhill, it is strictly prohibited to shut off the flame and slide, and it is restricted to brake all of a sudden while driving with tons unless there are special circumstances.
6. When the forklift is running, it should comply with the web traffic rules in the factory and should keep a specific security range from the automobile in front. .
7. When the forklift is running, the lots needs to be in the lowest position that does not hinder the driving, and the gantry needs to be appropriately tilted back. The tons shall not be increased except when stacking or loading. .
8. The height of the load should not obstruct the chauffeur's sight. In unique circumstances, when the thing impacts the forward vision, drive at a low rate when reversing.
9. It is prohibited to turn on the ramp, neither to drive across the ramp. .
10. The secure driving rate of the forklift in the manufacturing facility location is 5 km/h, and it should drive Stand-on Electric Pallet Stacker securely at a low speed when getting in the manufacturing workshop area. .
11. When the forklift is raised, lifted or driven, it is restricted for personnel to stand on the fork to hold items and play a stabilizing role. .
12. If problems are discovered, they will be fixed and reported in a timely manner, and they will certainly never ever operate with diseases or conceal them.

filling and unloading.
1. When fork-loading things, the distance between both forks need to be adjusted as needed to make the lots of both forks well balanced and not skewed, and one side of the item need to protest the shelf. .
2. It is prohibited to collaborate with a single fork or make use of a fork top or pull. In unique situations, safety indication need to be set up to remind bordering pedestrians. .
3. In the process of packing and dumping items, the forklift has to be braked with the brake. .
4. The speed of the vehicle must be slow-moving and stable. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled things and harm individuals. .
5. When utilizing a fork to fork the goods, the fork needs to be as deep as feasible under the load, and it should be noted that the fork tip must not touch other products or objects. The tons needs to be supported with minimal back tilt of the gantry to ensure that the load does not slide in reverse. The pole can be tilted forward somewhat when the tons is decreased to enable very easy positioning of the tons and extraction of the forks. .
6. It is prohibited to fork items at high speed and ram hard items with the fork head. .
7. When the forklift is functioning, it is forbidden for individuals to loaf the fork, so regarding stay clear of the collapse of the goods and harm people. .
8. Overloading is restricted, and it is forbidden to make use of forks to raise personnel to engage in high-altitude procedures to stay clear of high-altitude falling mishaps. .
9. It is not permitted to utilize the brake inertia to slip, put, round or roll things. .
10. It is not permitted to use forks to select, transform pallet dump.

Leaving .
1. It is restricted to leave the forklift when the things on the fork impend. Before leaving the forklift, you should unload the goods or lower the fork framework.
2. Pull the emergency brake handle to dead or depress the hand brake button.
3. The engine is shut off and the power is cut off. (Except for unique scenarios, such as the vehicle driver does not leave the lorry's view and does not go beyond 1 minute).
4. Get rid of the secret. .

Forklift Operation Precautions.
1. Prior to and after the forklift operation, the look should be examined, and gas, lubing oil and air conditioning water must be added.
2. Check the safety performance of starting, running and braking.
3. Examine whether the lights and horn signals are full and efficient.
4. Throughout the operation of the forklift, check whether the stress and temperature level are regular.
5. After the forklift is running, the outside leakage needs to also be examined and the seals ought to be changed in time.

Forklift Safety Operation Specifications.
1. You need to check before leaving the automobile;.
2. When you encounter a person before you throughout driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the cargo ought to be 0.3 m ~ 0.4 m in the air;.
5. The transforming should not be too sharp to stop the propensity of " complimentary turning";.
6. Adding and down the incline should be slow and consistent, and no activating the slope is allowed.
7. Do not drive throughout the slope. When the slope is greater than 10%, the vehicle ought to be driven backwards when declining;.
8. When the forklift employees carry the goods and move on, if they experience big or hefty goods and most likely to the chauffeur's line of vision, they should take the reversing exercise
.
The "Eight Prohibitions" need to be followed in the operation.
1. Single fork operation is not allowed.
2. It is not permitted to raise the goods for far away driving.
3. It is not enabled to grab the goods by handing over the pallet with the fork.
4. It is not permitted to straight shovel chemicals, flammables and other hazardous chemicals with forks.
5. It is not permitted to use inertia pressure to grab the goods.
6. It is not enabled to make use of stopping pressure to exile round or easy-to-roll objects.
7. It is not allowed to bring individuals to service the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is raised.
8. Do not drive laterally on slopes
.
Parking is not permitted under the list below problems.
1. Curves, narrow roads, railway crossings;.
2. Areas with a longitudinal slope more than 5%.
3. When there is an challenge on one side of the road, the contrary side of the section with the same length as the challenge should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected] Stand-on Electric Pallet Stacker
Phone：+86 13827083844